Search Results - Weekend Freedom Machines Forum | Vintage John Deere Tractors

Search:

Type: Posts; User: ed_lincoln

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    8
    Views
    103

    Just loosen the bolt and swing the @#$% out of...

    Just loosen the bolt and swing the @#$% out of the way.
  2. After swing the lift shaft to where the pin could...

    After swing the lift shaft to where the pin could be removed, it was rusted in. I bored a small hole in the frame rail and drove it out with a punch.
  3. Replies
    2
    Views
    206

    Look under the title :Technical Drawings: 332...

    Look under the title :Technical Drawings: 332 should be the same as 318 3 point plans/drawings PDF
  4. I would put a pulse type fuel pump. Make a metal...

    I would put a pulse type fuel pump. Make a metal plate to block off the hole in the block, thread for 1/4" hose fitting and use a pulse type pump as used on 318's ,Kawasaki or Briggs.
  5. Thread: The new guy

    by ed_lincoln
    Replies
    5
    Views
    517

    Front: 37 or 37a snow thrower, 43 blade, no.4...

    Front: 37 or 37a snow thrower, 43 blade, no.4 wood splitter. Under the tractor: 39 or 47 mower decks, grader blade, Haban sickle bar mower, Rear of the tractor: 80 cart, 31 roto tiller, and an...
  6. Replies
    11
    Views
    1,196

    Simplicity built MonkeyWard squire 9. I just...

    Simplicity built MonkeyWard squire 9. I just grabbed a picture to show they do not need to be resized using "GO Advanced"
  7. Replies
    11
    Views
    1,196

    I never resize just use "go Advanced" 248308

    I never resize just use "go Advanced"
    248308
  8. Replies
    11
    Views
    1,196

    See that row of figures/simbales above were you...

    See that row of figures/simbales above were you type the text the third simbale from the right end says insert a image/picture. use the go advanced or you may need to down size your picture.
  9. Replies
    27
    Views
    2,057

    I have a couple of those Gilson made Plymouth....

    I have a couple of those Gilson made Plymouth. Wisc. On the hood it says hydro 16. The engine is a Briggs horizontal shaft. I picked up tiller, sicklebar, front blade, snowblower and a integral...
  10. Thread: my tractors

    by ed_lincoln
    Replies
    13
    Views
    1,210

    Lewiston is at the S.E. corner were Wash, Ore,...

    Lewiston is at the S.E. corner were Wash, Ore, and Idaho come together. That canyon is most likely from the Snake river, Hells Canyon
  11. Replies
    8
    Views
    724

    You can put any type pulse fuel pump on a garden...

    You can put any type pulse fuel pump on a garden tractor by making a metal plate with a 1/4" hose fitting tapped into it. Remove the fuel pump, mount the plate connect the hoses and start it up....
  12. Replies
    16
    Views
    1,003

    What else do you have other than the electric...

    What else do you have other than the electric motor part? You'll need the front and rear pins to mount the electric motor part.
  13. Replies
    7
    Views
    514

    The later has a groove for the hyd lift pump that...

    The later has a groove for the hyd lift pump that mounts on top of the head. 3 groove total
  14. Replies
    7
    Views
    514

    Could be the early pulley doesn't have a gruve...

    Could be the early pulley doesn't have a gruve for a hyd lift belt
  15. Replies
    9
    Views
    987

    If you go and plug that number into the...

    If you go and plug that number into the registry(in YELLOW at the top of the page) it says it's a 1972 model 70. Someone may have replaced the hood
  16. Replies
    5
    Views
    514

    247274 247276 You need the electric lift helper...

    247274 247276 You need the electric lift helper spring kit.
  17. Replies
    2
    Views
    376

    Someone put that on to use with a non resistor...

    Someone put that on to use with a non resistor coil. So they used a car coil.
  18. Replies
    6
    Views
    837

    arms torn off in a grain auger at 2 1/2 years old.

    arms torn off in a grain auger at 2 1/2 years old.
  19. Replies
    36
    Views
    3,636

    If an ol fa like me can do it so can you: take...

    If an ol fa like me can do it so can you: take the big nuts off with a impact wrench, drive the 3/4" shaft down flush with the pulley, now the pulley needs to come off because the woodruff key is...
  20. Thread: New from CT

    by ed_lincoln
    Replies
    6
    Views
    498

    :welcome:Lots of help here if ya need it

    :welcome:Lots of help here if ya need it
  21. Replies
    10
    Views
    1,482

    What part of the country are you from? Might be...

    What part of the country are you from? Might be able to help with the missing parts. The hyd pump isn't from a 67 110, the round fender pump is driven off the pto pulley on the other side of the...
  22. Replies
    7
    Views
    633

    Take the fender pan off and disconnect the drive...

    Take the fender pan off and disconnect the drive shaft at the hydro pump, remove the hood and grill, pull the engine out drive shaft and all in one piece.
  23. Replies
    7
    Views
    633

    :welcome: Hello Lots of help here if you need it.

    :welcome: Hello Lots of help here if you need it.
  24. Replies
    34
    Views
    4,271

    Nice older 950 with a brush hog so I can mow...

    Nice older 950 with a brush hog so I can mow about 1 acre of black berry bushes, every year.
  25. Replies
    3,996
    Views
    319,340

    A friend of mine worked at Ft Lewis and removed 5...

    A friend of mine worked at Ft Lewis and removed 5 Wilton vises when the plumbers turned in the older trucks.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4