Possible Head Gasket Leak
Results 1 to 7 of 7

Thread: Possible Head Gasket Leak

  1. #1
    Senior Member
    Display Name: Bonecrusher

    Join Date
    Sep 2017
    Location
    IL
    Posts
    148
    Thanks
    1
    Thanked 17 Times in 15 Posts

    Possible Head Gasket Leak

    JD 110 RF k181- Today for the 2nd time in the history of me owning the tractor I mowed with it. First time I thought I heard a rod knock and stopped (almost 2 years ago) figured I would try again sometime in the future. Well today after about 30 minutes of mowing I noticed smoke coming out near the head. After letting the tractor cool down for a couple minutes it was fine. Is this a bad headgasket and possibly warped head? Or something else. I will say the tractor ran and mowed extremely well even with the smoke.
    Thanks for any help ~Reno

    Sent from my SM-N960U using Tapatalk

  2. Remove Advertisements
    WFMachines.com
    Advertisements
     

  3. #2
    Senior Member
    Display Name: Mike Grant

    Join Date
    Mar 2015
    Posts
    154
    Thanks
    22
    Thanked 23 Times in 18 Posts
    Get a light and inspect around the head gasket For oil. Will probably involve removing the engine tin. Look for a wet spot where the head meets the block. Is it a 110H? If so you might be having an issue with a leaking pump. This would result in hydraulic fluid leaking down on the motor, causing the smoke.
    Last edited by MGrant; 05-20-2020 at 05:19 PM.

  4. #3
    Senior Member
    Display Name: Bonecrusher

    Join Date
    Sep 2017
    Location
    IL
    Posts
    148
    Thanks
    1
    Thanked 17 Times in 15 Posts
    Nope not an a hydro lift just regular. I saw oil by the dip stick but not near the head. I will pull the tin and check tho.

    Sent from my SM-N960U using Tapatalk

  5. Remove Advertisements
    WFMachines.com
    Advertisements
     

  6. #4
    Senior Member
    Display Name: Mike Grant

    Join Date
    Mar 2015
    Posts
    154
    Thanks
    22
    Thanked 23 Times in 18 Posts
    I’s also give the valve cover area a good look. If possible thoroughly wipe the block dry and look for fresh oil when you start it. Given the age of an RF, leaking seeping gaskets are a given.

  7. #5
    Senior Member
    Display Name: Bill Fleisch
    smalljob's Avatar
    Join Date
    Jul 2013
    Location
    Southeastern MA
    Posts
    1,161
    Thanks
    9
    Thanked 186 Times in 162 Posts
    Once you have the tin off the top you can also put a socket wrench on the head bolts and see if any are loose. To set properly you should use a torque wrench, but just to check if they are loose or snug you should be Ok without one if you don't have it.

  8. The Following User Says Thank You to smalljob For This Useful Post:

    ed_lincoln (05-22-2020)

  9. #6
    Senior Member
    Display Name: Bonecrusher

    Join Date
    Sep 2017
    Location
    IL
    Posts
    148
    Thanks
    1
    Thanked 17 Times in 15 Posts
    Pulled all the tins off and could not find any evidence of a headgadket leak. But my head bolts where mismatched and not orginal. So i decided to pull the head and could see on the gasket where it had been leaking. The previous person did not clean the surfaces for the head gasket so it never sealed well.

    Sent from my SM-N960U using Tapatalk

  10. #7
    Senior Member
    Display Name: Bonecrusher

    Join Date
    Sep 2017
    Location
    IL
    Posts
    148
    Thanks
    1
    Thanked 17 Times in 15 Posts
    Update- replaced headgasket and it blew it out after about 15 minutes.

    Next day replaced with another new headgasket (glad I ordered a spare) and seems to be fine now. I think I somehow tightened the head to the wrong specs that or they loosened up.

    Going back in to double check that it hasnt loosened and it should be good to go. I will add that I found out the motor has been bored .040 over.. which I didnt even know they made.

    Sent from my SM-N960U using Tapatalk

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •